{"id":2484,"date":"2026-11-20T13:45:03","date_gmt":"2026-11-20T05:45:03","guid":{"rendered":"https:\/\/www.lycbearingcn.com\/news\/locating-non-locating-bearings-thermal-growth\/"},"modified":"2026-11-20T13:45:16","modified_gmt":"2026-11-20T05:45:16","slug":"locating-non-locating-bearings-thermal-growth","status":"publish","type":"post","link":"https:\/\/www.lycbearingcn.com\/ru\/news\/locating-non-locating-bearings-thermal-growth\/","title":{"rendered":"Locating and Non-Locating Bearings: A Thermal Growth Example"},"content":{"rendered":"<h1>Locating and Non-Locating Bearings: A Thermal Growth Example<\/h1>\n<p>Every two-bearing shaft arrangement asks the same question before it asks anything else:<br \/>\n<em>which bearing holds the shaft axially, and which one lets it move?<\/em> The reason is heat. A steel<br \/>\nshaft running 65&deg;C above ambient grows by about 0.23 mm over a 300 mm bearing span &mdash; and by<br \/>\nnearly 1.9 mm over a 4 m span. That growth has to go somewhere. If both bearings are clamped against<br \/>\nit, the expansion stops being motion and becomes force: a parasitic axial load that can be<br \/>\n<strong>fourteen times the design thrust<\/strong> and cut calculated life from tens of thousands of<br \/>\nhours to tens of hours.<\/p>\n<p>Bearing suppliers explain the principle correctly: one locating (fixed) bearing, one non-locating<br \/>\n(floating) bearing, and the formula &Delta;L = &alpha;&middot;L&middot;&Delta;T. Almost all of them stop<br \/>\nthere. This article takes the three steps they skip. We compute how much growth a real shaft makes<br \/>\n(including what an aluminium housing does differently), turn that into a <em>required axial float<\/em><br \/>\nwith installation allowance and safety factor, show the <em>life cliff<\/em> when the float provided is<br \/>\neven a few hundredths of a millimetre short, and then convert the answer into a bearing choice:<br \/>\ninternal float with an <a href=\"https:\/\/www.lycbearingcn.com\/ru\/products\/cylindrical-roller-bearings\/\">NU cylindrical roller<\/a>, an outer-ring<br \/>\nsliding fit with a <a href=\"https:\/\/www.lycbearingcn.com\/ru\/products\/deep-groove-ball-bearings\/\">deep groove ball bearing<\/a>, or a preloaded<br \/>\npaired arrangement.<\/p>\n<p>This is the third piece of a connected series. Our<br \/>\n<a href=\"https:\/\/www.lycbearingcn.com\/ru\/news\/bearing-load-calculation-shaft-forces-to-l10\/\">bearing load calculation guide<\/a> ended with a shaft whose floating seat A<br \/>\ncarried only 4.58 kN radial and whose locating seat B carried all 2.500 kN of axial thrust. This<br \/>\narticle explains <em>why<\/em> that split is deliberate and how much float seat A must provide to keep<br \/>\nit valid.<\/p>\n<p class=\"note\"><strong>About the numbers:<\/strong> the expansion coefficients, stiffness, allowance,<br \/>\nsafety factor, ratings and life figures below are <em>illustrative magnitudes for teaching the<br \/>\nmethod<\/em>, not catalogue values for any specific product. Substitute your actual geometry,<br \/>\ntemperatures, fits and manufacturer ratings before designing an arrangement.<\/p>\n<h2>1. Why two locating bearings is the classic installation error<\/h2>\n<p>Take a shaft held axially at both ends and heat it. Steel wants to elongate; the two bearings<br \/>\nrefuse to let it. The shaft cannot win, so it pushes on both bearings with a force set by the axial<br \/>\nstiffness of the shaft, the bearings and the housing. That force was never in the load calculation,<br \/>\nbecause it does not come from the machine&#8217;s duty &mdash; it comes from the installation itself.<\/p>\n<p>The consequences are distinctive, which is why an experienced engineer recognises them quickly:<\/p>\n<ul>\n<li><strong>Bearing temperature rises with no change in load.<\/strong> Extra axial force raises contact<br \/>\n      load, which raises friction, which raises temperature &mdash; a feedback loop.<\/li>\n<li><strong>Life collapses.<\/strong> In the worked case below, a fully restrained 0.234 mm of growth<br \/>\n      produces 35.1 kN of parasitic axial force and drops predicted life from 65,623 h to<br \/>\n      roughly <strong>42 h<\/strong>.<\/li>\n<li><strong>Failure looks like overload, not misinstallation.<\/strong> Raceways spall, preload climbs,<br \/>\n      and the report blames the bearing or the lubricant.<\/li>\n<\/ul>\n<p>The fix is a division of labour. The <strong>locating<\/strong> bearing is fixed to both shaft and<br \/>\nhousing and carries radial load plus axial load in both directions. The <strong>non-locating<\/strong><br \/>\nbearing carries radial load but is free to move axially, so it absorbs thermal growth without building<br \/>\nforce. Between them the shaft is positioned in space yet free to breathe.<\/p>\n<figure>\n  <img decoding=\"async\" src=\"https:\/\/www.lycbearingcn.com\/wp-content\/uploads\/2026\/06\/nu312-bearing.png\" alt=\"NU design cylindrical roller bearing\" \/><figcaption>An NU cylindrical roller bearing is the textbook floating seat: the rollers can move<br \/>\n  axially relative to the flangeless raceway, so both rings can be mounted with an interference fit<br \/>\n  while the bearing still floats internally.<\/figcaption><\/figure>\n<h2>2. The decision chain at a glance<\/h2>\n<p>Five steps, each with one output. The competitive literature covers step 1 and jumps to a bearing<br \/>\ntype. Steps 2 and 3 are where an arrangement succeeds or fails, and they are what this article adds.<\/p>\n<table>\n<thead>\n<tr>\n<th>Step<\/th>\n<th>What you compute<\/th>\n<th>Output<\/th>\n<th>Common trap<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>1<\/td>\n<td>Thermal growth of shaft relative to housing<\/td>\n<td>&Delta;L in mm<\/td>\n<td>Using ambient temperature instead of the running shaft temperature<\/td>\n<\/tr>\n<tr>\n<td>2<\/td>\n<td>Required float = growth + allowance, with safety factor<\/td>\n<td>s<sub>req<\/sub> in mm<\/td>\n<td>Matching float to &Delta;L with zero installation margin<\/td>\n<\/tr>\n<tr>\n<td>3<\/td>\n<td>Life penalty if available float falls short<\/td>\n<td>parasitic F, L<sub>10h<\/sub><\/td>\n<td>Assuming &#8220;a bit less float&#8221; is a small error<\/td>\n<\/tr>\n<tr>\n<td>4<\/td>\n<td>Float mechanism: internal, sliding fit, or paired arrangement<\/td>\n<td>Bearing family<\/td>\n<td>Choosing an NUP when a floating bearing is needed<\/td>\n<\/tr>\n<tr>\n<td>5<\/td>\n<td>Which end locates, and the fits on each ring<\/td>\n<td>Arrangement drawing<\/td>\n<td>Letting the housing dictate the locating end arbitrarily<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<h2>3. Step 1 &mdash; how much does the shaft actually grow?<\/h2>\n<p>The basic relation is &Delta;L = &alpha;&middot;L&middot;&Delta;T, where &alpha; is the linear<br \/>\nexpansion coefficient (about 12 &times; 10<sup>&minus;6<\/sup> \/&deg;C for steel), L is the distance<br \/>\nbetween the locating bearing and the floating bearing, and &Delta;T is the shaft&#8217;s temperature rise<br \/>\nfrom assembly to running condition.<\/p>\n<p>Keep the model conservative: assume the housing stays near ambient while the shaft reaches its<br \/>\nrunning temperature. That makes the whole shaft expansion the floating seat&#8217;s problem, which is the<br \/>\nsafe way to design.<\/p>\n<p style=\"text-align:center;font-size:16px\"><strong>&Delta;L = &alpha; &middot; L &middot; &Delta;T<\/strong><\/p>\n<p><strong>Case A<\/strong> is the 300 mm-span gear drive from our load-calculation article: the shaft<br \/>\nruns 65&deg;C above ambient (20&deg;C &rarr; 85&deg;C). <strong>Case B<\/strong> is a long dryer or<br \/>\nconveyor drum shaft, 2,400 mm between bearings, 45&deg;C rise.<\/p>\n<table>\n<thead>\n<tr>\n<th>Case<\/th>\n<th>Span L<\/th>\n<th>&Delta;T<\/th>\n<th>&Delta;L = &alpha;L&Delta;T<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>A &mdash; compact gear drive<\/td>\n<td>300 mm<\/td>\n<td>65&deg;C<\/td>\n<td>12e&minus;6 &times; 300 &times; 65 = <strong>0.234 mm<\/strong><\/td>\n<\/tr>\n<tr>\n<td>B &mdash; long drum shaft<\/td>\n<td>2,400 mm<\/td>\n<td>45&deg;C<\/td>\n<td>12e&minus;6 &times; 2,400 &times; 45 = <strong>1.296 mm<\/strong><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>A single number is misleading because growth scales with both length and temperature. This grid<br \/>\nshows the same steel shaft at several spans and rises; it is the quickest way to see whether thermal<br \/>\ngrowth is a rounding detail or a design driver.<\/p>\n<table>\n<thead>\n<tr>\n<th>Span L<\/th>\n<th>&Delta;T = 30&deg;C<\/th>\n<th>&Delta;T = 45&deg;C<\/th>\n<th>&Delta;T = 65&deg;C<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>300 mm<\/td>\n<td>0.108 mm<\/td>\n<td>0.162 mm<\/td>\n<td>0.234 mm<\/td>\n<\/tr>\n<tr>\n<td>600 mm<\/td>\n<td>0.216 mm<\/td>\n<td>0.324 mm<\/td>\n<td>0.468 mm<\/td>\n<\/tr>\n<tr>\n<td>1,000 mm<\/td>\n<td>0.360 mm<\/td>\n<td>0.540 mm<\/td>\n<td>0.780 mm<\/td>\n<\/tr>\n<tr>\n<td>1,500 mm<\/td>\n<td>0.540 mm<\/td>\n<td>0.810 mm<\/td>\n<td>1.170 mm<\/td>\n<\/tr>\n<tr>\n<td>2,400 mm<\/td>\n<td>0.864 mm<\/td>\n<td>1.296 mm<\/td>\n<td>1.872 mm<\/td>\n<\/tr>\n<tr>\n<td>4,000 mm<\/td>\n<td>1.440 mm<\/td>\n<td>2.160 mm<\/td>\n<td><strong>3.120 mm<\/strong><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>Below roughly 0.2 mm, a standard bearing&#8217;s internal clearance can quietly absorb the growth and<br \/>\nthe arrangement is forgiving. Above about 1 mm, growth becomes the dominant axial design constraint<br \/>\nand the float mechanism must be chosen deliberately. A 4 m shaft at 65&deg;C needs more than 3 mm of<br \/>\ntravel &mdash; far beyond what a deep groove ball bearing sliding in its housing can reliably give.<\/p>\n<h2>4. Step 2 &mdash; from growth to required axial float<\/h2>\n<p>The float you must design in is not equal to &Delta;L. Two more quantities belong in the sum: an<br \/>\n<strong>installation allowance<\/strong> for tolerance stack-up (shoulder positions, housing bore<br \/>\ndepth, thermal growth during assembly, measurement error) and a <strong>safety factor<\/strong> for<br \/>\nuncertainty in the running temperature.<\/p>\n<p style=\"text-align:center;font-size:16px\"><strong>s<sub>req<\/sub> = f<sub>s<\/sub> &middot; (&Delta;L + allowance)<\/strong><\/p>\n<p>Using an illustrative allowance of 0.10 mm and a safety factor f<sub>s<\/sub> = 1.30:<\/p>\n<table>\n<thead>\n<tr>\n<th>Case<\/th>\n<th>&Delta;L<\/th>\n<th>Allowance<\/th>\n<th>f<sub>s<\/sub><\/th>\n<th>Required float s<sub>req<\/sub><\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>A &mdash; 300 mm gear drive<\/td>\n<td>0.234 mm<\/td>\n<td>0.10 mm<\/td>\n<td>1.30<\/td>\n<td><strong>0.434 mm<\/strong><\/td>\n<\/tr>\n<tr>\n<td>B &mdash; 2,400 mm drum<\/td>\n<td>1.296 mm<\/td>\n<td>0.10 mm<\/td>\n<td>1.30<\/td>\n<td><strong>1.815 mm<\/strong><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>Note that safety is applied to the whole bracket, including the allowance &mdash; growth you did<br \/>\nnot budget for is the one that hurts. Notice also how the allowance, fixed at 0.10 mm, matters<br \/>\ngreatly for the short shaft (it is nearly a third of the growth) and negligibly for the long one.<br \/>\nShort shafts are dominated by installation tolerance; long shafts by expansion itself.<\/p>\n<p>The number on the drawing should be a <em>minimum<\/em> travel with the shaft at its cold position,<br \/>\nplus a clear statement of which direction the shaft grows and where the locating datum is. &#8220;Allow<br \/>\nfor thermal expansion&#8221; is not a manufacturable instruction; &#8220;floating bearing to provide at least<br \/>\n0.45 mm axial travel from the cold position toward the gear&#8221; is.<\/p>\n<h2>5. Step 3 &mdash; the life cliff when float runs short<\/h2>\n<p>This is the calculation almost nobody publishes, and it is the reason a float specification<br \/>\ndeserves the same attention as a load rating. Treat the shaft and bearing stack as a spring with an<br \/>\naxial stiffness k &mdash; an illustrative 150 kN\/mm here. If the bearing provides float <em>s<\/em> but<br \/>\nthe shaft grew by &Delta;L, the shortfall &delta; = &Delta;L &minus; s is converted into parasitic<br \/>\naxial force:<\/p>\n<p style=\"text-align:center;font-size:16px\"><strong>F<sub>parasitic<\/sub> = k &middot; (&Delta;L &minus; s)<\/strong><\/p>\n<p>Add that force to the locating bearing&#8217;s axial load and recompute the equivalent dynamic load,<br \/>\nusing the same illustrative factors as the <a href=\"https:\/\/www.lycbearingcn.com\/ru\/news\/bearing-load-calculation-shaft-forces-to-l10\/\">load-calculation article<\/a><br \/>\n(f<sub>d<\/sub> = 1.3, X = 0.67, Y = 2.9, F<sub>r<\/sub> = 8.0 kN, design F<sub>a<\/sub> = 2.5 kN,<br \/>\nC = 178 kN, p = 10\/3, 23.15 h per million revolutions). Case A needs 0.234 mm of float:<\/p>\n<table>\n<thead>\n<tr>\n<th>Float provided s<\/th>\n<th>Shortfall &delta;<\/th>\n<th>Parasitic F<\/th>\n<th>F<sub>a<\/sub> total<\/th>\n<th>P<\/th>\n<th>L<sub>10h<\/sub><\/th>\n<th>vs design<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>0 mm (both ends fixed)<\/td>\n<td>0.234 mm<\/td>\n<td>35.1 kN<\/td>\n<td>37.6 kN<\/td>\n<td>148.7 kN<\/td>\n<td><strong>42 h<\/strong><\/td>\n<td>0.1%<\/td>\n<\/tr>\n<tr>\n<td>0.100 mm<\/td>\n<td>0.134 mm<\/td>\n<td>20.1 kN<\/td>\n<td>22.6 kN<\/td>\n<td>92.2 kN<\/td>\n<td><strong>208 h<\/strong><\/td>\n<td>0.3%<\/td>\n<\/tr>\n<tr>\n<td>0.150 mm<\/td>\n<td>0.084 mm<\/td>\n<td>12.6 kN<\/td>\n<td>15.1 kN<\/td>\n<td>63.9 kN<\/td>\n<td>704 h<\/td>\n<td>1.1%<\/td>\n<\/tr>\n<tr>\n<td>0.200 mm<\/td>\n<td>0.034 mm<\/td>\n<td>5.1 kN<\/td>\n<td>7.6 kN<\/td>\n<td>35.6 kN<\/td>\n<td><strong>4,939 h<\/strong><\/td>\n<td>7.5%<\/td>\n<\/tr>\n<tr>\n<td><strong>0.234 mm (exact)<\/strong><\/td>\n<td>0<\/td>\n<td>0<\/td>\n<td>2.5 kN<\/td>\n<td>16.39 kN<\/td>\n<td><strong>65,623 h<\/strong><\/td>\n<td>100%<\/td>\n<\/tr>\n<tr>\n<td>0.434 mm (= s<sub>req<\/sub>)<\/td>\n<td>0<\/td>\n<td>0<\/td>\n<td>2.5 kN<\/td>\n<td>16.39 kN<\/td>\n<td>65,623 h<\/td>\n<td>100%<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>Read the last two rows carefully. Providing <em>exactly<\/em> the growth (0.234 mm) already recovers<br \/>\nfull design life; the extra allowance is insurance against uncertainty, not extra capacity. But<br \/>\nmissing it by only <strong>0.034 mm<\/strong> &mdash; 0.200 mm provided against 0.234 mm needed, a 15%<br \/>\nshortfall &mdash; still costs <strong>92% of calculated life<\/strong>. There is no gradual degradation<br \/>\nhere. Because life scales with (C\/P)<sup>10\/3<\/sup> and P has a large axial term, float shortfall is<br \/>\namplified into a cliff.<\/p>\n<p>For Case B the arithmetic is brutal: a fully restrained 1.296 mm of growth at the same stiffness<br \/>\nwould generate 194.4 kN of parasitic force, well beyond what a bearing of this class can carry. Long<br \/>\nshafts are not a borderline case &mdash; they must have a positive, verified float mechanism.<\/p>\n<p class=\"warn\">The model assumes the entire shortfall loads the locating bearing and uses an<br \/>\nillustrative axial stiffness. Real stiffness depends on the bearing, fits and housing; the point of<br \/>\nthe table is the <em>shape<\/em> of the curve &mdash; a steep, nonlinear penalty &mdash; not the exact<br \/>\nhour figures.<\/p>\n<h2>6. Step 4 &mdash; three ways to make a bearing float<\/h2>\n<p>Once the required float is known, choose a mechanism. There are three, and they are not<br \/>\ninterchangeable.<\/p>\n<table>\n<thead>\n<tr>\n<th>Mechanism<\/th>\n<th>How it floats<\/th>\n<th>Typical travel*<\/th>\n<th>Ring fits<\/th>\n<th>Best for<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td><strong>Internal float<\/strong> &mdash; NU \/ N cylindrical roller<\/td>\n<td>Rollers move axially on the flangeless raceway<\/td>\n<td>~1.5&ndash;3.0 mm<\/td>\n<td>Both rings can be interference fits<\/td>\n<td>High radial load, high speed, no axial constraint<\/td>\n<\/tr>\n<tr>\n<td><strong>Outer-ring sliding fit<\/strong> &mdash; deep groove \/ spherical roller<\/td>\n<td>Outer ring slides in the housing bore<\/td>\n<td>~&plusmn;1&ndash;2 mm, seat limited<\/td>\n<td>Inner ring interference, outer ring clearance (H6\/G6)<\/td>\n<td>Moderate duty, simple housing, short travel<\/td>\n<\/tr>\n<tr>\n<td><strong>Adjusted \/ paired arrangement<\/strong> &mdash; opposed angular contact or tapered pair<\/td>\n<td>Set clearance or light preload between the two bearings<\/td>\n<td>Set at assembly, not free float<\/td>\n<td>Both rings located; adjust with shims \/ nut<\/td>\n<td>Rigid, precise shafts; short spans; gear positioning<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p style=\"font-size:13px;color:#6b7686\">*Illustrative travel ranges. Always take the actual permissible<br \/>\naxial displacement from the manufacturer&#8217;s catalogue for the specific bearing and fits.<\/p>\n<p>Internal float is the cleanest solution because the movement happens inside the bearing: both rings<br \/>\ncan be clamped, so there is no fretting between an outer ring and a housing bore. Its limit is that<br \/>\nit gives no axial location at all &mdash; a pure NU or N bearing cannot locate the shaft in either<br \/>\ndirection, so the <em>other<\/em> end must do it.<\/p>\n<p>An outer-ring sliding fit is cheap and works for short travel, but the sliding happens under the<br \/>\nbearing&#8217;s full radial load. On a heavily loaded spherical roller that sliding force can be large<br \/>\nenough to resist movement or fret the housing bore; it is a common source of &#8220;the bearing was fine<br \/>\nbut the housing wore out&#8221;. See our note on<br \/>\n<a href=\"https:\/\/www.lycbearingcn.com\/ru\/news\/the-importance-of-bearing-clearance\/\">bearing clearance<\/a> for how the operating fit changes once the machine<br \/>\nis hot.<\/p>\n<p>An adjusted pair does not float freely at all: it sets a defined clearance or light preload. It is<br \/>\nexcellent for rigidity and axial positioning on short shafts, but it is the wrong answer when the<br \/>\nrequired growth from step 2 is large &mdash; a preloaded pair cannot absorb 1.8 mm of expansion.<\/p>\n<h2>7. Internal float: the NU cylindrical roller solution<\/h2>\n<p>An <a href=\"https:\/\/www.lycbearingcn.com\/ru\/products\/cylindrical-roller-bearings\/\">NU cylindrical roller bearing<\/a> has two ribs on the inner ring<br \/>\nand none on the outer ring (an N bearing reverses this). The rollers can travel axially along the<br \/>\nflangeless raceway, so the bearing accommodates shaft growth internally. Because no external sliding<br \/>\nis needed, the inner ring can be an interference fit on the shaft and the outer ring an interference<br \/>\nfit in the housing &mdash; eliminating ring creep at both seats.<\/p>\n<table>\n<thead>\n<tr>\n<th>Design point<\/th>\n<th>Recommendation<\/th>\n<th>Why<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Internal axial travel<\/td>\n<td>&ge; s<sub>req<\/sub> plus margin<\/td>\n<td>Check catalogue permissible displacement for the chosen size and fits<\/td>\n<\/tr>\n<tr>\n<td>Inner ring fit<\/td>\n<td>Interference (e.g. k6\/m6 family)<\/td>\n<td>Prevent the ring creeping on a rotating shaft under radial load<\/td>\n<\/tr>\n<tr>\n<td>Outer ring fit<\/td>\n<td>Interference or transition<\/td>\n<td>No sliding needed; avoid housing-bore fretting<\/td>\n<\/tr>\n<tr>\n<td>Minimum radial load<\/td>\n<td>Verify<\/td>\n<td>Rollers can skid if radial load is too low for the speed<\/td>\n<\/tr>\n<tr>\n<td>Location duty<\/td>\n<td>None &mdash; pair with a locating bearing<\/td>\n<td>NU\/N carry no axial load and cannot position the shaft<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>For Case A (s<sub>req<\/sub> = 0.434 mm) a standard NU of the right series has ample internal travel.<br \/>\nFor Case B (1.815 mm) the travel must be checked explicitly: some sizes offer enough, others do not,<br \/>\nand a design that assumes &#8220;cylindrical rollers float&#8221; without verifying the number has repeated the<br \/>\noriginal mistake at a worse scale.<\/p>\n<figure>\n  <img decoding=\"async\" src=\"https:\/\/www.lycbearingcn.com\/wp-content\/uploads\/2026\/06\/22220-bearing.png\" alt=\"Spherical roller bearing\" \/><figcaption>At the locating end, a self-aligning spherical roller bearing handles radial load plus<br \/>\n  thrust in both directions. It belongs opposite the floating NU, not in the floating seat under<br \/>\n  heavy radial load where outer-ring sliding would be required.<\/figcaption><\/figure>\n<h2>8. Outer-ring sliding fit: deep groove and spherical roller options<\/h2>\n<p>If radial load is modest and travel is short, a<br \/>\n<a href=\"https:\/\/www.lycbearingcn.com\/ru\/products\/deep-groove-ball-bearings\/\">deep groove ball bearing<\/a> can float by sliding its outer ring in the<br \/>\nhousing bore with a clearance fit (a G6\/H6-type housing fit in illustrative terms), while the inner<br \/>\nring stays clamped to the shaft. A<br \/>\n<a href=\"https:\/\/www.lycbearingcn.com\/ru\/products\/spherical-roller-bearings\/\">spherical roller bearing<\/a> can be used the same way when<br \/>\nmisalignment demands self-aligning capability.<\/p>\n<p>The sliding fit trades simplicity for three risks:<\/p>\n<ul>\n<li><strong>Travel is seat-limited.<\/strong> The outer ring can only slide as far as the housing<br \/>\n      shoulders allow, typically &plusmn;1&ndash;2 mm in ordinary arrangements &mdash; not enough for<br \/>\n      Case B.<\/li>\n<li><strong>Sliding happens under load.<\/strong> With the full radial reaction pressing the outer<br \/>\n      ring into the bore, the friction that resists movement is not small. Thermal growth can be<br \/>\n      partly absorbed by elastic deflection instead of sliding, recreating the parasitic-force problem.<\/li>\n<li><strong>Fretting corrosion.<\/strong> Machine vibration rocks a loosely fitted outer ring in its<br \/>\n      bore, producing the rust-coloured smear and black powder that<br \/>\n      <a href=\"https:\/\/www.lycbearingcn.com\/ru\/news\/the-types-of-ball-bearings\/\">failure analysts recognise as fretting<\/a>.<\/li>\n<\/ul>\n<p>If this mechanism is chosen, specify the housing fit explicitly, keep the bore surface finish and<br \/>\nroundness tight, and confirm that the available travel exceeds s<sub>req<\/sub> with the ring at its<br \/>\ncold-position limit. A deep groove ball bearing used this way still needs a separate locating bearing<br \/>\nat the other end; it cannot take thrust and float at the same time. Our<br \/>\n<a href=\"https:\/\/www.lycbearingcn.com\/ru\/news\/characteristics-and-differences-between-angular-contact-bearings-and-deep-groove-ball-bearings\/\">angular contact vs deep groove comparison<\/a> explains why the deep<br \/>\ngroove bearing&#8217;s axial capacity is limited when a genuine locating function is needed.<\/p>\n<figure>\n  <img decoding=\"async\" src=\"https:\/\/www.lycbearingcn.com\/wp-content\/uploads\/2026\/06\/Deep-Groove-Ball-Bearing-1.png\" alt=\"Single row deep groove ball bearing\" \/><figcaption>A deep groove ball bearing can serve as the floating seat with a sliding outer-ring fit,<br \/>\n  but its travel is limited by the housing shoulders and it transfers no axial load.<\/figcaption><\/figure>\n<h2>9. The third option: an adjusted pair<\/h2>\n<p>For short, stiff shafts where axial positioning matters &mdash; machine spindles, precise gear<br \/>\nmounting, wheel hubs &mdash; the answer is often not &#8220;one fixed, one floating&#8221; but two bearings<br \/>\nmounted against each other. Opposed<br \/>\n<a href=\"https:\/\/www.lycbearingcn.com\/ru\/products\/angular-contact-ball-bearings\/\">angular contact ball bearings<\/a> \u0438\u043b\u0438<br \/>\n<a href=\"https:\/\/www.lycbearingcn.com\/ru\/products\/tapered-roller-bearings\/\">tapered roller bearings<\/a> are set with a defined clearance or light<br \/>\npreload, giving high rigidity and accurate axial location.<\/p>\n<p>The trade-off is that an adjusted pair consumes the thermal-growth budget at assembly. It has no<br \/>\nfree float; any expansion shows up as a change in preload. That is acceptable when the span is short<br \/>\nand the temperature rise modest, and dangerous when step 2 returned more than about a millimetre.<br \/>\nFor a long, hot shaft the usual pattern is a locating adjusted pair at one end and an NU floating<br \/>\nbearing at the other &mdash; rigidity where it matters, float where it is needed. Our<br \/>\n<a href=\"https:\/\/www.lycbearingcn.com\/ru\/news\/tapered-roller-bearing-selection-guide-and-luoyang-inno-bearings-customized-service\/\">tapered roller bearing selection guide<\/a> covers preload and endplay setting<br \/>\nfor the locating pair.<\/p>\n<p>A <a href=\"https:\/\/www.lycbearingcn.com\/ru\/products\/thrust-ball-bearings\/\">thrust bearing<\/a> is not a solution to floating. It carries axial<br \/>\nload in one direction only, cannot locate both ways on its own, and must be paired with a radial<br \/>\nbearing; dropping one into a shaft that also carries 8 kN radial accomplishes none of the float<br \/>\nrequirements calculated above.<\/p>\n<figure>\n  <img decoding=\"async\" src=\"https:\/\/www.lycbearingcn.com\/wp-content\/uploads\/2026\/06\/Angular-Contact-Ball-Bearing.png\" alt=\"Angular contact ball bearing\" \/><figcaption>Opposed angular contact bearings provide precise axial location and high stiffness,<br \/>\n  but they are set at assembly and cannot absorb large thermal growth on a long shaft.<\/figcaption><\/figure>\n<h2>10. Step 5 &mdash; which end should locate?<\/h2>\n<p>Once the float mechanism is settled, decide which seat is fixed. Three rules, in priority order:<\/p>\n<ol>\n<li><strong>Where the axial load already is.<\/strong> In the gear drive from article #3, the helical<br \/>\n      gear generates 2.500 kN of thrust. Letting the bearing nearest the gear locate keeps that force<br \/>\n      on the shortest, stiffest load path; that is why seat B was chosen as the locating bearing and<br \/>\n      seat A as floating.<\/li>\n<li><strong>Short distance to the heat source and the locating datum.<\/strong> Put the locating<br \/>\n      bearing where the shaft&#8217;s axial position is measured from, so growth proceeds away from a known<br \/>\n      reference toward the floating end.<\/li>\n<li><strong>Access for adjustment.<\/strong> The locating end often needs shims or a locknut to set<br \/>\n      preload or endplay; put it where a fitter can reach it.<\/li>\n<\/ol>\n<p>Write the decision on the drawing: which bearing locates, the cold-position datum, the direction of<br \/>\ngrowth, and the minimum travel the floating end must provide. Ambiguity here is what produces the<br \/>\n&#8220;both ends clamped&#8221; installation in the first place.<\/p>\n<p>A special case is the slow-rotating structure &mdash; a crane turntable or excavator ring &mdash;<br \/>\nwhere the &#8220;shaft&#8221; is a ring bolted to a frame and the load case is axial force plus tilting moment,<br \/>\nnot gear thrust. The locating\/floating logic still applies to how the ring is supported, but the<br \/>\nnumbers come from a different model; see our<br \/>\n<a href=\"https:\/\/www.lycbearingcn.com\/ru\/news\/how-to-choose-the-right-slewing-bearing\/\">slewing bearing selection overview<\/a> and the<br \/>\n<a href=\"https:\/\/www.lycbearingcn.com\/ru\/news\/crossed-roller-vs-ball-slewing-bearings\/\">crossed roller vs ball comparison<\/a>.<\/p>\n<figure>\n  <img decoding=\"async\" src=\"https:\/\/www.lycbearingcn.com\/wp-content\/uploads\/2026\/06\/cross-roller-slewing-bearing-2.png\" alt=\"Crossed roller slewing bearing\" \/><figcaption>In slewing rings the load case is built from axial force, radial force and tilting<br \/>\n  moment at the bolt circle rather than from shaft reactions.<\/figcaption><\/figure>\n<h2>11. Housing material and differential expansion<\/h2>\n<p>So far the housing has been treated as static. In reality it expands too, and what matters is the<br \/>\n<em>difference<\/em> between shaft and housing. Using the same 300 mm span and 65&deg;C rise, with<br \/>\nillustrative housing coefficients:<\/p>\n<table>\n<thead>\n<tr>\n<th>Housing material<\/th>\n<th>&alpha; housing<\/th>\n<th>Relative growth vs steel shaft*<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Cast iron<\/td>\n<td>~10.5 &times; 10<sup>&minus;6<\/sup><\/td>\n<td>0.029 mm<\/td>\n<\/tr>\n<tr>\n<td>Steel<\/td>\n<td>~12 &times; 10<sup>&minus;6<\/sup><\/td>\n<td>0 mm (matched)<\/td>\n<\/tr>\n<tr>\n<td>Aluminium<\/td>\n<td>~23 &times; 10<sup>&minus;6<\/sup><\/td>\n<td><strong>0.215 mm<\/strong><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p style=\"font-size:13px;color:#6b7686\">*If both reach the same temperature. The sign reverses if the<br \/>\nhousing runs hotter than the shaft; use the actual running temperatures in both parts.<\/p>\n<p>An aluminium housing expands almost twice as much as the steel shaft over the same temperature<br \/>\nrise. If the shaft is hotter &mdash; the usual case in a gearbox &mdash; the two partially cancel and<br \/>\nthe required float is smaller than the conservative estimate. If the housing is the hotter part (an<br \/>\nexternally heated drum, a sun-lit outdoor pedestal), the relative movement reverses and the float must<br \/>\nbe provided in the opposite direction. Either way the aluminium case is nearly as large as the entire<br \/>\nsteel-shaft growth in Case A, so it cannot be ignored.<\/p>\n<p>This is why an arrangement copied from a cast-iron housing into an aluminium one can fail: the<br \/>\ngeometry and the bearings are identical, but the differential expansion budget changed by an order of<br \/>\nmagnitude. Check the housing coefficient and its running temperature before signing off any float<br \/>\nfigure.<\/p>\n<h2>12. Worked decision: the gear-drive shaft from article #3<\/h2>\n<p>Put the whole chain together on the shaft we already sized. Step 1 gave the loads: floating seat A<br \/>\nat 4.58 kN radial, locating seat B at 8.04 kN radial plus 2.500 kN axial. Add the thermal model from<br \/>\nthis article with an illustrative 300 mm span, 65&deg;C shaft rise, steel housing:<\/p>\n<table>\n<thead>\n<tr>\n<th>Question<\/th>\n<th>Result<\/th>\n<th>Decision<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>How much does the shaft grow?<\/td>\n<td>&Delta;L = 0.234 mm<\/td>\n<td>Float is mandatory, not optional<\/td>\n<\/tr>\n<tr>\n<td>Required float?<\/td>\n<td>s<sub>req<\/sub> = 0.434 mm<\/td>\n<td>Specify &ge; 0.45 mm at cold position<\/td>\n<\/tr>\n<tr>\n<td>Cost of a 0.034 mm shortfall?<\/td>\n<td>Life 4,939 h vs 65,623 h<\/td>\n<td>Design margin is cheap; do not skip it<\/td>\n<\/tr>\n<tr>\n<td>Float mechanism?<\/td>\n<td>Internal float ~1.5&ndash;3 mm available<\/td>\n<td>NU cylindrical roller at seat A<\/td>\n<\/tr>\n<tr>\n<td>Locating bearing?<\/td>\n<td>Carries Fr 8.04 kN + Fa 2.500 kN<\/td>\n<td>Spherical roller at seat B (per selection guide)<\/td>\n<\/tr>\n<tr>\n<td>Ring fits?<\/td>\n<td>A: both rings clamped; B: inner clamped, outer located<\/td>\n<td>No sliding at either seat<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>The result is a coherent arrangement: an NU floating bearing that needs no housing sliding, a<br \/>\nlocating spherical roller that takes the gear thrust on the shortest load path, and a drawing that<br \/>\nstates the cold-position float explicitly. It is the same pair of seats the<br \/>\n<a href=\"https:\/\/www.lycbearingcn.com\/ru\/news\/bearing-load-calculation-shaft-forces-to-l10\/\">load-calculation article<\/a> arrived at &mdash; now with the thermal reason and<br \/>\nthe float number behind it.<\/p>\n<p>For the heavy-duty end of the range, the same reasoning applies with larger forces and longer<br \/>\nspans; our <a href=\"https:\/\/www.lycbearingcn.com\/ru\/news\/selecting-the-right-rolling-mill-bearings-is-crucial-for-steel-mills-luoyang-inno-bearings-safeguards-production\/\">rolling mill bearing notes<\/a> and<br \/>\n<a href=\"https:\/\/www.lycbearingcn.com\/ru\/news\/spherical-cylindrical-roller-bearings-the-core-solution-for-industrial-transmission\/\">spherical &amp; cylindrical roller guide<\/a> cover that class.<\/p>\n<figure>\n  <img decoding=\"async\" src=\"https:\/\/www.lycbearingcn.com\/wp-content\/uploads\/2026\/06\/Rolling-Mill-Bearing-2.png\" alt=\"Rolling mill bearing\" \/><figcaption>In heavy mill and drum shafts, spans are long and temperatures high, so thermal growth<br \/>\n  is a first-order constraint on the arrangement rather than a detail.<\/figcaption><\/figure>\n<h2>13. Eight mistakes that turn growth into a bearing failure<\/h2>\n<table>\n<thead>\n<tr>\n<th>Mistake<\/th>\n<th>What happens<\/th>\n<th>Fix<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Clamp both bearings axially<\/td>\n<td>Growth becomes parasitic force; life collapses<\/td>\n<td>One locating, one floating seat<\/td>\n<\/tr>\n<tr>\n<td>Size float to &Delta;L with no allowance<\/td>\n<td>Tolerance stack-up consumes the margin<\/td>\n<td>Add installation allowance and safety factor<\/td>\n<\/tr>\n<tr>\n<td>Use an NUP as the floating bearing<\/td>\n<td>NUP locates both ways and cannot float; it restrains growth<\/td>\n<td>Use NU or N for internal float<\/td>\n<\/tr>\n<tr>\n<td>Specify &#8220;allow for expansion&#8221; on the drawing<\/td>\n<td>Not manufacturable or verifiable<\/td>\n<td>State minimum travel, datum and growth direction<\/td>\n<\/tr>\n<tr>\n<td>Use a sliding outer-ring fit under heavy radial load<\/td>\n<td>High sliding force, fretting, housing-bore wear<\/td>\n<td>Use internal float with both rings clamped<\/td>\n<\/tr>\n<tr>\n<td>Ignore housing material<\/td>\n<td>Aluminium moves ~0.215 mm differently in Case A<\/td>\n<td>Include housing coefficient and temperature<\/td>\n<\/tr>\n<tr>\n<td>Assume the housing stays cold without checking<\/td>\n<td>Differential expansion sign can reverse<\/td>\n<td>Measure or estimate both running temperatures<\/td>\n<\/tr>\n<tr>\n<td>Reuse a preloaded pair on a long, hot shaft<\/td>\n<td>Preload climbs with growth; no float budget<\/td>\n<td>Locating pair at one end, NU float at the other<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>Every one of these is an installation or specification decision, not a bearing-quality problem.<br \/>\nThat is the point: the bearing is usually the last thing to blame and the first thing to replace.<\/p>\n<h2>14. What to put on the drawing and what to measure<\/h2>\n<p>A float arrangement is only as good as the information given to the person assembling it. This is<br \/>\nthe minimum set we ask for when reviewing a drawing:<\/p>\n<table>\n<thead>\n<tr>\n<th>Item<\/th>\n<th>Why it is needed<\/th>\n<th>How it is obtained<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Shaft and housing running temperatures<\/td>\n<td>Set &Delta;T for both parts<\/td>\n<td>Measurement on a running machine, or duty estimate<\/td>\n<\/tr>\n<tr>\n<td>Distance from locating bearing to floating bearing<\/td>\n<td>The length L in &alpha;L&Delta;T<\/td>\n<td>Assembly drawing<\/td>\n<\/tr>\n<tr>\n<td>Minimum axial travel at the floating seat<\/td>\n<td>The manufacturable expression of s<sub>req<\/sub><\/td>\n<td>Step 2 calculation<\/td>\n<\/tr>\n<tr>\n<td>Which bearing locates; cold-position datum<\/td>\n<td>Defines the direction of growth<\/td>\n<td>Arrangement decision, step 5<\/td>\n<\/tr>\n<tr>\n<td>Fit class for each ring at both seats<\/td>\n<td>Prevents creep and unintended sliding<\/td>\n<td>Load and float mechanism<\/td>\n<\/tr>\n<tr>\n<td>Permissible axial displacement of the chosen bearing<\/td>\n<td>Confirms the mechanism can deliver s<sub>req<\/sub><\/td>\n<td>Manufacturer catalogue<\/td>\n<\/tr>\n<tr>\n<td>Endplay or preload setting method<\/td>\n<td>Reproducible assembly for a locating pair<\/td>\n<td>Shim stack, locknut torque, or gauge<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>On the machine, the useful checks are simple: measure the housing temperature at the bearing seats<br \/>\nafter a heat soak, confirm the shaft can be pushed axially by at least the specified amount with the<br \/>\nmachine cold and stopped, and record the axial position of the shaft relative to the housing at<br \/>\nassembly. A bearing that runs hot shortly after a rebuild is often telling you that this float was<br \/>\nnever actually present.<\/p>\n<h2>Send us the arrangement, get the float checked<\/h2>\n<p>The chain above is what our engineers run before recommending a locating\/floating arrangement:<br \/>\nspan, running temperatures, shaft and housing materials, the loads at each seat, and the fits you plan<br \/>\nto use. Send us those inputs and we will return the required axial float, the parasitic-force and life<br \/>\nimpact if it is short, and the bearing families that can deliver the travel &mdash; including what has<br \/>\nto change in the housing if none of them can.<br \/>\n<a href=\"https:\/\/www.lycbearingcn.com\/ru\/contact-us\/\">Send your arrangement data to our engineering team<\/a>.<\/p>\n<p>You can also browse our <a href=\"https:\/\/www.lycbearingcn.com\/ru\/products\/cylindrical-roller-bearings\/\">cylindrical roller<\/a>,<br \/>\n<a href=\"https:\/\/www.lycbearingcn.com\/ru\/products\/deep-groove-ball-bearings\/\">deep groove ball<\/a>,<br \/>\n<a href=\"https:\/\/www.lycbearingcn.com\/ru\/products\/spherical-roller-bearings\/\">spherical roller<\/a>,<br \/>\n<a href=\"https:\/\/www.lycbearingcn.com\/ru\/products\/tapered-roller-bearings\/\">tapered roller<\/a> and<br \/>\n<a href=\"https:\/\/www.lycbearingcn.com\/ru\/products\/angular-contact-ball-bearings\/\">angular contact<\/a> bearing families for the types that appear in this<br \/>\ndecision.<\/p>\n<h2>Related reading<\/h2>\n<ul>\n<li><a href=\"https:\/\/www.lycbearingcn.com\/ru\/news\/bearing-load-calculation-shaft-forces-to-l10\/\">Bearing Load Calculation: From Shaft Forces to Fr, Fa and L10<\/a> &mdash;<br \/>\n      the shaft whose axial split (A floating, B locating) this article explains.<\/li>\n<li><a href=\"https:\/\/www.lycbearingcn.com\/ru\/news\/bearing-type-selection-decision-matrix\/\">Bearing Type Selection: A Decision Matrix with a Worked Example<\/a> &mdash;<br \/>\n      how the load case becomes a bearing choice.<\/li>\n<li><a href=\"https:\/\/www.lycbearingcn.com\/ru\/news\/the-importance-of-bearing-clearance\/\">\u0412\u0430\u0436\u043d\u043e\u0441\u0442\u044c \u0437\u0430\u0437\u043e\u0440\u0430 \u0432 \u043f\u043e\u0434\u0448\u0438\u043f\u043d\u0438\u043a\u0430\u0445<\/a> &mdash; what fits and<br \/>\n      temperature do to the clearance you selected.<\/li>\n<li><a href=\"https:\/\/www.lycbearingcn.com\/ru\/news\/spherical-cylindrical-roller-bearings-the-core-solution-for-industrial-transmission\/\">Spherical &amp; Cylindrical Roller Bearings<\/a> &mdash; the locating and<br \/>\n      floating roller families used in the worked arrangement.<\/li>\n<li><a href=\"https:\/\/www.lycbearingcn.com\/ru\/news\/tapered-roller-bearing-selection-guide-and-luoyang-inno-bearings-customized-service\/\">Tapered Roller Bearing Selection Guide<\/a> &mdash; preload and endplay<br \/>\n      for an adjusted locating pair.<\/li>\n<li><a href=\"https:\/\/www.lycbearingcn.com\/ru\/news\/characteristics-and-differences-between-angular-contact-bearings-and-deep-groove-ball-bearings\/\">Angular Contact vs Deep Groove Ball Bearings<\/a> &mdash; axial<br \/>\n      capacity and X\/Y factors when choosing the locating bearing.<\/li>\n<li><a href=\"https:\/\/www.lycbearingcn.com\/ru\/news\/the-types-of-ball-bearings\/\">The Types of Ball Bearings<\/a> &mdash; ball families including the<br \/>\n      sliding-fit floating option.<\/li>\n<li><a href=\"https:\/\/www.lycbearingcn.com\/ru\/news\/how-to-choose-the-right-slewing-bearing\/\">How to Choose the Right Slewing Bearing<\/a> &mdash; the alternative<br \/>\n      load model for slow-rotating structures.<\/li>\n<\/ul>\n<figure>\n  <img decoding=\"async\" src=\"https:\/\/www.lycbearingcn.com\/wp-content\/uploads\/2026\/06\/Single-Row-Tapered-Roller-Bearing.png\" alt=\"Single row tapered roller bearing\" \/><figcaption>An opposed tapered roller pair is a rigid locating option for short shafts; combine<br \/>\n  it with a floating NU at the other end when the span is long.<\/figcaption><\/figure>\n<h2>Frequently Asked Questions<\/h2>\n<h3>What is the difference between a locating and a non-locating bearing?<\/h3>\n<p>The locating (fixed) bearing holds the shaft axially in both directions and carries radial plus axial load. The non-locating (floating) bearing carries radial load but is free to move axially, so it absorbs thermal growth without building force. A typical arrangement uses one of each.<\/p>\n<h3>How much does a bearing shaft expand with temperature?<\/h3>\n<p>Use dL = alpha * L * dT. For steel, alpha is about 12e-6 per degC. A 300 mm shaft rising 65 degC grows 0.234 mm; a 2,400 mm shaft rising 45 degC grows 1.296 mm. Growth scales with both span and temperature rise, so long hot shafts need a deliberately sized float.<\/p>\n<h3>Which bearing type is used as a floating bearing?<\/h3>\n<p>An NU or N cylindrical roller bearing floats internally because the rollers can move axially along a flangeless raceway, allowing both rings to be interference-fitted. A deep groove ball bearing with a sliding outer-ring fit is a cheaper option for short travel. An NUP bearing does NOT float &#8211; it locates in both directions.<\/p>\n<h3>What happens if thermal expansion is restrained?<\/h3>\n<p>The growth turns into parasitic axial force F = k * shortfall. In the worked case a fully restrained 0.234 mm produces 35.1 kN &#8211; about 14 times the 2.5 kN design thrust &#8211; and cuts calculated L10 life from 65,623 h to about 42 h.<\/p>\n<h3>How much axial float should I design in?<\/h3>\n<p>Required float = safety factor * (thermal growth + installation allowance). With an illustrative 0.10 mm allowance and 1.30 safety factor, 0.234 mm of growth needs 0.434 mm of travel. Specify it as a minimum from the cold position, plus the growth direction, on the drawing.<\/p>\n<h3>Can a deep groove ball bearing be used as a floating bearing?<\/h3>\n<p>Yes, with a clearance fit between its outer ring and the housing bore. Its travel is limited (roughly +\/-1-2 mm in ordinary seats), and sliding under heavy radial load can cause fretting and housing wear. Internal-float cylindrical roller bearings are preferred for heavy duty or long travel.<\/p>\n<h3>Does the housing material matter for thermal growth?<\/h3>\n<p>Yes. What counts is shaft-versus-housing differential expansion. Over a 300 mm span at 65 degC, an aluminium housing moves about 0.215 mm differently from a steel shaft, while cast iron is only about 0.029 mm. Check both materials&#x27; coefficients and running temperatures.<\/p>\n<h3>Can a preloaded bearing pair accommodate thermal growth?<\/h3>\n<p>Only a little. An opposed angular-contact or tapered pair is set at assembly and has no free float; expansion raises preload. For a long hot shaft, use a locating pair at one end and a floating NU cylindrical roller bearing at the other.<\/p>\n<p><script type=\"application\/ld+json\">{\"@context\": \"https:\/\/schema.org\", \"@type\": \"FAQPage\", \"mainEntity\": [{\"@type\": \"Question\", \"name\": \"What is the difference between a locating and a non-locating bearing?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"The locating (fixed) bearing holds the shaft axially in both directions and carries radial plus axial load. The non-locating (floating) bearing carries radial load but is free to move axially, so it absorbs thermal growth without building force. A typical arrangement uses one of each.\"}}, {\"@type\": \"Question\", \"name\": \"How much does a bearing shaft expand with temperature?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Use dL = alpha * L * dT. For steel, alpha is about 12e-6 per degC. A 300 mm shaft rising 65 degC grows 0.234 mm; a 2,400 mm shaft rising 45 degC grows 1.296 mm. Growth scales with both span and temperature rise, so long hot shafts need a deliberately sized float.\"}}, {\"@type\": \"Question\", \"name\": \"Which bearing type is used as a floating bearing?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"An NU or N cylindrical roller bearing floats internally because the rollers can move axially along a flangeless raceway, allowing both rings to be interference-fitted. A deep groove ball bearing with a sliding outer-ring fit is a cheaper option for short travel. An NUP bearing does NOT float - it locates in both directions.\"}}, {\"@type\": \"Question\", \"name\": \"What happens if thermal expansion is restrained?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"The growth turns into parasitic axial force F = k * shortfall. In the worked case a fully restrained 0.234 mm produces 35.1 kN - about 14 times the 2.5 kN design thrust - and cuts calculated L10 life from 65,623 h to about 42 h.\"}}, {\"@type\": \"Question\", \"name\": \"How much axial float should I design in?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Required float = safety factor * (thermal growth + installation allowance). With an illustrative 0.10 mm allowance and 1.30 safety factor, 0.234 mm of growth needs 0.434 mm of travel. Specify it as a minimum from the cold position, plus the growth direction, on the drawing.\"}}, {\"@type\": \"Question\", \"name\": \"Can a deep groove ball bearing be used as a floating bearing?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Yes, with a clearance fit between its outer ring and the housing bore. Its travel is limited (roughly +\/-1-2 mm in ordinary seats), and sliding under heavy radial load can cause fretting and housing wear. Internal-float cylindrical roller bearings are preferred for heavy duty or long travel.\"}}, {\"@type\": \"Question\", \"name\": \"Does the housing material matter for thermal growth?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Yes. What counts is shaft-versus-housing differential expansion. Over a 300 mm span at 65 degC, an aluminium housing moves about 0.215 mm differently from a steel shaft, while cast iron is only about 0.029 mm. Check both materials' coefficients and running temperatures.\"}}, {\"@type\": \"Question\", \"name\": \"Can a preloaded bearing pair accommodate thermal growth?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Only a little. An opposed angular-contact or tapered pair is set at assembly and has no free float; expansion raises preload. For a long hot shaft, use a locating pair at one end and a floating NU cylindrical roller bearing at the other.\"}}]}<\/script><br \/>\n<script type=\"application\/ld+json\">{\"@context\": \"https:\/\/schema.org\", \"@type\": \"Article\", \"headline\": \"Locating and Non-Locating Bearings: A Thermal Growth Example\", \"description\": \"Locating vs non-locating bearings: thermal growth, required axial float, the sharp life penalty when float runs short, and how to choose the floating type.\", \"author\": {\"@type\": \"Organization\", \"name\": \"LUOYANG INNO BEARING CO., LTD\"}, \"publisher\": {\"@type\": \"Organization\", \"name\": \"LUOYANG INNO BEARING CO., LTD\"}, \"mainEntityOfPage\": {\"@type\": \"WebPage\", \"@id\": \"https:\/\/www.lycbearingcn.com\/news\/locating-non-locating-bearings-thermal-growth\/\"}}<\/script><\/p>","protected":false},"excerpt":{"rendered":"<p>Locating vs non-locating bearings: thermal growth, required axial float, the sharp life penalty when float runs short, and how to choose the floating type.<\/p>","protected":false},"author":1,"featured_media":2284,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[17,12,15,16],"_links":{"self":[{"href":"https:\/\/www.lycbearingcn.com\/ru\/wp-json\/wp\/v2\/posts\/2484"}],"collection":[{"href":"https:\/\/www.lycbearingcn.com\/ru\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.lycbearingcn.com\/ru\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.lycbearingcn.com\/ru\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.lycbearingcn.com\/ru\/wp-json\/wp\/v2\/comments?post=2484"}],"version-history":[{"count":1,"href":"https:\/\/www.lycbearingcn.com\/ru\/wp-json\/wp\/v2\/posts\/2484\/revisions"}],"predecessor-version":[{"id":2485,"href":"https:\/\/www.lycbearingcn.com\/ru\/wp-json\/wp\/v2\/posts\/2484\/revisions\/2485"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.lycbearingcn.com\/ru\/wp-json\/wp\/v2\/media\/2284"}],"wp:attachment":[{"href":"https:\/\/www.lycbearingcn.com\/ru\/wp-json\/wp\/v2\/media?parent=2484"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.lycbearingcn.com\/ru\/wp-json\/wp\/v2\/categories?post=2484"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.lycbearingcn.com\/ru\/wp-json\/wp\/v2\/tags?post=2484"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}